In order to check for proper installation, run checks to. Small mechanical hand rotation, to confirm that the rotate smoothly. Check the project due to foreign body, caused by scars, indentation to seize up, because of the bad installation, mounting process arising out of the bad moments are not stable, owing to the clearance is too small, caused by installation errors, seal friction torque is too large, and so on. Without exception you can start power function.
Bearing temperature, generally according to the external temperature of the bearing seat to speculate. Uses of oil hole directly measure the temperature of FAG bearings outer ring is more accurate. Self-aligning roller bearing temperature, from a running start rising, usually temperature-stable after 1-2 hours. Bad if the bearings are mounted, the temperature rises dramatically, exception occurred at high temperature. The reason such as excessive lubricant, bearing clearance is too small, poor installation, sealing device too much friction. Occasions of high speed rotation, selection of bearing structures, lubrication is also the cause of the error.
To fully meet the load bearing capacity of spherical roller bearing, the bearing inner and outer rings (or after the shaft washer of the thrust bearing washers) the entire circumference must be completely solid and uniform support, seating can be cylindrical or conical surfaces, in order to check for proper installation, run checks to. Small mechanical hand rotation, to confirm that the rotate smoothly. Check the project due to foreign body, caused by scars, indentation to seize up, because of the bad installation, mounting process arising out of the bad moments are not stable, owing to the clearance is too small, caused by installation errors, seal friction torque is too large, and so on. Without exception you can start power function.
FAG bearings for shaft and washer, then apply a smooth surface. Therefore, mating surfaces with the bearing ring process must reach a certain degree of accuracy, and not have any grooves, holes or other discrete shape. In addition, flange bearing rings must be securely fixed to prevent under load, spherical roller bearing in its rotating between the mating surfaces.
1, part of plant used to check for proper installation, run checks to. Small mechanical hand rotation, to confirm that the rotate smoothly. Check the project due to foreign body, caused by scars, indentation to seize up, because of the bad installation, mounting process arising out of the bad moments are not stable, owing to the clearance is too small, caused by installation errors, seal friction torque is too large, and so on. Without exception you can start power function.
FAG bearings applied to accommodate radial loads in the radial and axial combined loading, usually with two sets of FAG bearings pair used, mainly in the automotive front and rear wheels, active, differential bevel gear, gear reducer, transmission parts.
2, allows speeds: installed properly, lubrication good environment, allowing for bearing limit speed of 0.3-0.5 times times. Under normal circumstances, to 0.2 times the speed limit of the most desirable.
3, allowing tilting angle: spherical roller bearings are generally do not allow relative tilt the housing bore axis, such as tilt, maximum of 2 '.
4, allowing temperatures: under normal load, and with high temperature performance of lubricants and lubrication under adequate conditions, General bearings allow the at-30 degrees centigrade-150 ℃ environment temperature.
Bearings are removed when you intend to continue using after, you should use the appropriate removal tool. Demolition of the interference fit rings, on the rally can only be added to the ring, and should never be allowed to pass through the rolling force removal, or rolling elements and raceways were bruised. Lubricant is important not only for bearings, FAG bearings for all. But note that spherical roller bearings should not be adding too much grease. Then there is the replacement of the lubricant. Used oil lubricated bearings after purging old oil, if possible, should be poured into the fresh oil and let the machine at low speed of rotation for a few minutes. Oil collects residual contaminants as much as possible, and then purging these oils. The use of grease lubricated bearings when replacing the grease, used by Joe in addition should avoid contact with cotton to the fag bearing any of the parts. Fiber because these residues may be between wedge on scroll and causing damage, spherical roller bearings, in particular more attention to this issue.




Other News:
FAG spherical roller bearings running fever after maintenance factor to be taken into account by
Timken bearing three installation methods
NSK bearing temperature and vibration analysis of common
Prevention of FAG tapered roller bearings fault matters requiring attention
Common quality defects after heat treatment, the INA bearing parts problem
Failure analysis of affecting the TIMKEN bearing service life of
Effects of Taper roller bearings NSK stable operation failure to periodically check method
INA bearing maintenance, cleaning and maintenance