1, thrust bearing angular contact ball bearings
Axial angular contact ball bearing contact angle of 60 ° commonly used general thrust angular contact ball bearings are generally two-way thrust angular contact ball bearings, mainly used for precision machine tool spindle, usually with double row cylindrical roller bearings used in conjunction, can withstand two-way axial to load, with high accuracy, good rigidity, low temperature, high speed, easy assembly and disassembly.
2, bearing deep groove ball bearings
Deep groove ball bearings in the structure of each ring has a cross-section of the equatorial circumference of the ball one-third of the continuous groove type raceway. Deep groove ball bearings are mainly used to bear radial load, but also bear certain axial load. When SKF Bearings radial clearance increases, with the nature of angular contact ball bearings, can withstand both directions alternating axial load. With the same size compared to other types of bearings, such bearings friction, high limiting speed, high precision, user selection is the preferred bearing type. Deep groove ball bearing structure is simple, easy to use, is the largest production volume, most widely used of a class of bearings.
3, the bearing thrust tapered roller bearings
Since thrust tapered roller bearings rolling body is tapered roller, rolling in the structure of the bus and the bus were raceway washers intersect at a point bearing axis line, and thus can form pure rolling rolling surface, high speed limit in thrust cylindrical roller bearings. Features: Thrust tapered roller bearings can withstand a one-way axial load. Thrust tapered roller bearing type code 90000.
4, bearing double row tapered roller bearing structure, performance characteristics
Double row tapered roller bearings range, the maximum amount is 35 000 type, with one pair of outer and two inner ring raceway, there is an interval between the two inner circle, changing the thickness of the spacer adjustable clearance. These bearings radial load at the same time can withstand axial load in the axial bearing clearance range limit axial displacement of shaft and housing. Tapered roller bearing structural features. Tapered roller bearing type code 30000, tapered roller bearings are separable bearings. Tapered roller bearings are mainly used to bear radial load mainly radial and axial joint load. And angular contact ball bearings, bearing capacity, low speed limits. Tapered roller bearings can withstand axial load in one direction, the shaft or housing to limit axial displacement in one direction.
In order to give full play to SKF bearings and long-term to maintain its proper performance, you must do a good job of regular maintenance (periodic inspection).
By appropriate periodic inspection, so that early detection of failure to prevent accidents in the first place, to improve the productivity and economic importance.
1, cleaning
Remove the bearing inspection, photography and other methods to do first with the appearance of records. In addition, to confirm the remaining amount of lubricant and lubricant samples, and then cleaning bearings.
a, bearing cleaning of rough wash and sperm washing and can be placed in the bottom of the container used metal grid.
b, coarse wash, brush, etc. used in the oil or grease removal adhesive material. At this point if rotating bearings in oil, attention and other damage due to foreign objects rolling surface.
c, sperm washing, in the oil slowly rotating SKF bearings should be carefully carried out.
Commonly used cleaning agents for the neutral water diesel or kerosene, is sometimes necessary to use warm lye. Regardless of what kind of cleaning agent filter should always be kept clean.
Cleaned immediately after anti-rust coating on the bearing grease oil or rust.
2, check with the judge
In order to determine whether the re-use of the removed bearing should focus on checking the accuracy of its size, rotation accuracy, internal clearance and with the surface, raceway, cage and ring.
On the inspection results, may be used to bearings or SKF bearings were judged proficient.
Determine the mechanical properties and the criteria according to the degree of importance and checking cycles vary. If the following injury, the bearings must not be reused and must be replaced.
1) bearing parts breakage and defects.
2) rolling surface raceway material peeling.
Bearing fault identification method
Not by removing checks to identify or predict the bearing in operation without failure, to improve productivity and economy are very important.
The main identification methods are as follows:
1) identified by voice
Identify needs through sound experience. Must be adequately trained to recognize SKF bearings achieve sound and non-bearing sound. To do this, you should try to carry out this work by hand. A listening or listening rods attached to the housing can clearly hear the sound of the bearing.
2) identification of the operating temperature
This method is relatively identification method is limited to use in the operation state is not changing situations. Therefore, the temperature must be continuously recorded. Fails, only the temperature rises, there will be irregular changes.
3) to identify the state of the lubricant
The lubricant sampling and analysis, through its pollution level is mixed with foreign matter or metal powders to judge. This method does not close observation bearings or large bearings are particularly effective.



Other News:
Bearing vibration testing standards and the application of vibration measuring instrument approach
SKF bearing structure types on different maintenance requirements
Scraping of sliding bearing grinding technical requirements
FAG Bearings reasons arising from the use excitation detection and analysis
Spherical roller bearings running four factors of failure
Analysis of the engine lubrication of journal bearing
TIMKEN bearing life influence the causes and maintenance measures
Needle bearing lubrication problems improper treatment of burn